DS200SLCCG1ADC DS200SHVMG1A DS200SDCIG1AFB DS200SDCIG1AEB DS200GDPAG1AKF通用电气卡件DS3800HSCC1D DS3800HPTN1D1D DS3800HPBC DS3800HLND1C1C DS3800HLNA1D1A DS3800HFPB1F1E DS3800HDDL DS3800HARA1B1C DS3800DFXD-1B1B DS200SLCCG4A SIM卡选择MVME162的Z85230串行通信控制器的端口B为可通过安装在连接器上的串行接口模块（SIM）进行配置MVME162板上的J10。有四个串行接口模块可用：❏ EIA-232-D（DCE和DTE）❏ EIA-530（DCE和DTE）通过安装适当的串行接口模块，您可以将端口B从EIA-232-D更改为EIA-530接口（或反之亦然）。
端口B已路由（通过J10处的SIM卡）连接到标记为串行的25针DB25前面板连接器端口2。有关MVME162上SIM连接器J10的位置，请参阅图2-1。图2-2说明了串行接口模块的二次侧（底部）显示插入SIM卡连接器J10的J1连接器MVME162。图2-3（第3-6页）、图2-4（第3-4页）和图2-5说明端口B的可用配置。有关串行接口模块的零件号，请参阅表2-1。这个零件号通常打印在SIM的一次侧（顶部），但在某些版本中，可以在二次侧找到。如果需要用另一个SIM卡替换现有的串行接口模块键入，转到下面的删除现有SIM卡。如果主板上没有SIM卡，跳到安装新SIM卡。安装新SIM卡1.观察SIM卡接头J1和J1上的连接器按键的方向MVME162接头J10。转动SIM卡，使钥匙对齐并放置将其轻轻地安装在连接器J10上，对齐SIM卡角落处的安装孔与MVME162上的对峙相匹配。2、轻轻按下SIM卡顶部，将其固定在连接器上。如果SIM卡有不要轻轻按压座椅，重新检查方向。如果SIM卡连接器如果方向不正确，安装孔将与对峙。3.放置两个4-40 x 3/您以前使用过的16“十字头螺钉拆下（或与新SIM一起提供）到两个相对的角安装孔中。将他们拧入僵局，但不要过紧。各种串行通信中的信号关系和信号连接端口A和B的可用配置如图2-3、2-4、，和2-5。SIM Selection
Port B of the MVME162’s Z85230 serial communications controller is
configurable via a serial interface module (SIM) which is installed at connector
J10 on the MVME162 board. Four serial interface modules are available:
❏ EIA-232-D (DCE and DTE)
❏ EIA-530 (DCE and DTE)
You can change Port B from an EIA-232-D to an EIA-530 interface (or viceversa) by mounting the appropriate serial interface module. Port B is routed
(via the SIM at J10) to the 25-pin DB25 front panel connector marked SERIAL
PORT 2.
For the location of SIM connector J10 on the MVME162, refer to Figure 2-1.
Figure 2-2 illustrates the secondary side (bottom) of a serial interface module,
showing the J1 connector which plugs into SIM connector J10 on the
MVME162. Figure 2-3 (sheets 3-6), Figure 2-4 (sheets 3-4), and Figure 2-5
illustrate the configurations available for Port B.
For the part numbers of the serial interface modules, refer to Table 2-1. The
part numbers are ordinarily printed on the primary side (top) of the SIMs, but
may be found on the secondary side in some versions.
If you need to replace an existing serial interface module with a SIM of another
type, go to Removal of Existing SIM below. If there is no SIM on the main board,
skip to Installation of New SIM.Installation of New SIM
1. Observe the orientation of the connector keys on SIM connector J1 and
MVME162 connector J10. Turn the SIM so that the keys line up and place
it gently on connector J10, aligning the mounting holes at the SIM corners
with the matching standoffs on the MVME162.
2. Gently press the top of the SIM to seat it on the connector. If the SIM does
not seat with gentle pressure, recheck the orientation. If the SIM connector
is oriented incorrectly, the mounting holes will not line up with the
standoffs.3. Place the two 4-40 x 3
/16” Phillips-head screws that you previously
removed (or that were supplied with the new SIM) into the two oppositecorner mounting holes. Screw them into the standoffs but do not
overtighten them.
The signal relationships and signal connections in the various serial
configurations available for ports A and B are illustrated in Figures 2-3, 2-4,
and 2-5.
