oracle监听配置.md

最近在工作中需要测试oracle监听，通过扒拉资料和请教一些同事，先做一些操作上的总结吧，先看下监听中的很多名词
- 动态监听：动态注册不需要从listener.ora中读取配置文件，实例在mount时，pmon进程会根据instance_name,service_name参数将实例和服务动态注册到listerer中
- 静态监听：静态注册指实例启动时读取listener.ora配置文件，将实例和服务注册到监听程序
  - 如图所示:状态是UNKNOW的是静态监听，状态是READY是动态监听
    
    image.png
  - 静态监听配置方法
    - RAC: 配置在grid下，配置路径$ORACLE_HOME/network/admin/listener.ora
    - 单实例（无GI）：配置在oracle下,配置路径$ORACLE_HOME/network/admin/listener.ora
    - 配置监听的三种情况
      - 一个监听在一个IP一个端口上监听多个实例
      - 一个监听在一个IP一个端口上监听多个实例

# 注意SID_LIST_ORCL和ORCL 的名称需要一致
# 启动监听：lsnrctl start orcl
# 关闭监听：lsnrctl stop orcl
# 监听状态：lsnrctl status orcl
# 一个监听在一个IP一个端口上监听多个实例
SID_LIST_ORCL =
  (SID_LIST =
    (SID_DESC =
      (GLOBAL_DBNAME = ORCL)
      (ORACLE_HOME = /opt/oracle/products/12.2.0.2)
      (SID_NAME = ORCL)
    )
    (SID_DESC =
      (GLOBAL_DBNAME = NHL)
      (ORACLE_HOME = /opt/oracle/products/12.2.0.2)
      (SID_NAME = NHL)
    )
  )
ORCL =
  (DESCRIPTION_LIST =
    (DESCRIPTION =
      (ADDRESS = (PROTOCOL = TCP)(HOST = 0.0.0.0)(PORT = 1521))
    )
    (DESCRIPTION =
      (ADDRESS = (PROTOCOL = IPC)(KEY = EXTPROC))
    )
  )
# 一个监听在一个IP不同端口上监听多个实例
SID_LIST_ORCL =
  (SID_LIST =
    (SID_DESC =
      (GLOBAL_DBNAME = ORCL)
      (ORACLE_HOME = /opt/oracle/products/12.2.0.2)
      (SID_NAME = ORCL)
    )
    (SID_DESC =
      (GLOBAL_DBNAME = NHL)
      (ORACLE_HOME = /opt/oracle/products/12.2.0.2)
      (SID_NAME = NHL)
    )
  )
ORCL =
  (DESCRIPTION_LIST =
    (DESCRIPTION =
      (ADDRESS = (PROTOCOL = TCP)(HOST = 0.0.0.0)(PORT = 1521))
    )
    (DESCRIPTION =
      (ADDRESS = (PROTOCOL = TCP)(HOST = 0.0.0.0)(PORT = 1522))
    )
    (DESCRIPTION =
      (ADDRESS = (PROTOCOL = IPC)(KEY = EXTPROC))
    )
  )
# 多个监听监听多个实例
SID_LIST_ORCL =
  (SID_LIST =
    (SID_DESC =
      (GLOBAL_DBNAME = ORCL)
      (ORACLE_HOME = /opt/oracle/products/12.2.0.2)
      (SID_NAME = ORCL)
    )
    (SID_DESC =
      (GLOBAL_DBNAME = NHL)
      (SID_NAME = NHL)
    )
  )
ORCL =
    (DESCRIPTION =
      (ADDRESS = (PROTOCOL = TCP)(HOST = 0.0.0.0)(PORT = 1521))
    ）
SID_LIST_TEST =
  (SID_LIST =
    (SID_DESC =
      (GLOBAL_DBNAME = TEST)
      (ORACLE_HOME = /opt/oracle/products/12.2.0.2)
      (SID_NAME = TEST)
    )
   ）
TEST =
   (DESCRIPTION =
      (ADDRESS = (PROTOCOL = TCP)(HOST = 0.0.0.0)(PORT = 1523))
    )

安装完RAC后默认的监听地址（本地监听和scan 监听）

LISTENER_SCAN1 =
  (DESCRIPTION =
    (ADDRESS_LIST =
      (ADDRESS = (PROTOCOL = IPC)(KEY = LISTENER_SCAN1))
    )
  )

LISTENER =
  (DESCRIPTION =
    (ADDRESS_LIST =
      (ADDRESS = (PROTOCOL = IPC)(KEY = LISTENER))
    )
  )

配置完成后需要手工注册监听地址

方法一：
alter system register    # 手动给监听注册service
方法二：
- 单实例
alter system set local_listener='(address=(protocol=tcp)(host=0.0.0.0)(port=1522))';
- RAC
alter system set local_listener='(ADDRESS=(PROTOCOL=tcp)(HOST=0.0.0.0)(PORT=1523))' scope=both sid='orcl';

参考链接：
参考1
参考2

最后编辑于：2019.05.29 15:57:06