QuestPro接口
当QuestPro（用于辨识的过程测试数据生成器）可用时，若QuestPro应用于控制器，控制视图上将显示以下参数。
可以使用“Client Window Builder（客户端窗口构建器）”配置显示位置。默认值是控制面板的最后一列。
显示条件如下：
1）若有任一使用QuestPro的控制器，并且任务状态不为OFF。
2）QuestPro启动后显示以下参数。
3）所有任务状态变为OFF后，以下参数将不显示。
表B 5.2控制视图
|条目 |描述| 操作员 | 工程师|
| ------------- |:-------------:| -----:|
|Quest Status（Quest状态）| 显示QuestPro状态。 0:OFF 1:STANDBY 2:ACTIVE 3:CONTROL 4. ******: QuestPro不应用。| R |R|
|Quest WDG timer (sec)计时器| QuestPro应用的Watch dog 计时器。 默认视图为不显示。请使用Client Window Builder（客户端窗口构建器）定义它。| R |R|
|Current EF filter time constant（当前EF滤波器时间常数）| EF滤波器的倾斜时间常数。QuestPro可通过多次更改EF滤波器来移动POV和MV。 默认视图为不显示。请使用Client Window Builder（客户端窗口构建器）定义它。| R |R|
|Original EF filter time constant（原始EF滤波器时间常数） |连接QuetPro之前的EF滤波器时间常数。| R |R|
为了改变MV和POV的动态行为，在优化模式下QuestPro将更改EF时间常数。
子控制器
| 条目| 描述| 操作员 | 工程师|
| ------------- |:-------------:| -----:|
| Sub Controller（子控制器）| Exasmoc子控制器的唯一Tag名。 | R| R|
| Actual Status（实际状态） | 当前控制状态。| R | R|
| Desired Status（期望状态）| 在此条目的组合框帮助下，可以选择/更改各个子控制器的状态。 单击组合框。 将显示删除菜单。 ACTIVE INACTIVE 如下所述，为子控制器操作选择一种模式。 ACTIVE :根据主控制器的实际状态计算控制动作并输出到过程/HMI。 INACTIVE : 仅执行模型更新观察。不计算控制动作。| R/W R/W | R/W R/W|
| Comment（评论）| 控制器评论 (16字符)。| R | R|
CALC计算
| 条目| 描述 | 操作员模式 | 工程师模式|
| ------------- |:-------------:| -----:|
| Sub Controller（子控制器） | 定义了计算后，“CALC”将显示在树状图中，分别定义了计算的次数。| R | R|
| Actual Status（实际状态）| 当前控制状态。| R | R|
| Desired Status（所需状态）| 可以选择计算状态。 仅在ENG模式下可选择。 ACTIVE INACTIVE ACTIVE:执行计算，且结果显示在屏幕上。 当DCS位号名被定义为输出地址时，计算结果将发送到DCS。 INACTIVE:执行计算，但不显示在屏幕上或输出到DCS。 在MC/SC概述面板上,将保留以前计算的值。| R | R/W|
| Comment（评论）| 控制器评论 (16字符)。| R | R|
原文：
QuestPro interface
When QuestPro (Process test data generator for identification) is available, the following parameters are displayed on the control view when QuestPro is applied to the controller.
The display location can be configurable using ‘Client Window Builder’. Default is the last column of the control panel.
The display conditions are as follows:
- There exists any controller which uses QuestPro.and the Quest status is not OFF.
- The below parameters are displayed after QuestPro starts.
- The below parameters become undisplayed after all Quest status become OFF.
Table B 5.2 Control view
| Item | Description | Operator | Engineer|
| ------------- |:-------------:| -----:|
| Quest Status| QuestPro status is shown. 0:OFF 1:STANDBY 2:ACTIVE 3:CONTROL 4. ******: QuestPro is not applied. |R| R|
|Quest WDG timer (sec)| Watch dog timer for QuestPro application. Default view does not display it. Please define it using Client Window Builder. |R |R|
|Current EF filter time constant| EF filter tilter time constant. QuestPro changes EF filter several times to move POV and MV. Default view does not display it. Please define it using Client Window Builder.| R |R|
|Original EF filter time constant |EF filter time constant before QuetPro is connected. | R |R|
In order to move MV and POV dynamic behavior, QuestPro changes EF time constant in the Optimise mode.
Sub Controller
|Item |Description | Operator | Engineer|
| ------------- |:-------------:| -----:|
|Sub Controller |Exasmoc Sub Controllerˇs unique Tag Name | R | R|
|Actual Status |Current control Status| R | R|
|Desired Status|With the help of Combo box under this item individual sub-controllerˇs Status can be selected/changed. Click Combo box. Drop out menu will appear. ACTIVE INACTIVE Select one of the modes for sub-controllerˇs action as described below. ACTIVE : Control actions are computed and output to the process/HMI according to the actual status of the main controller. INACTIVE : Only observation is performed for model updating. No control actions are computed.| R/W R/W |R/W R/W|
|Comment| Controllerˇs Comments (16 Characters) |R |R|
CALC calculation
|Item | Description| Operator mode |Engineer mode|
| ------------- |:-------------:| -----:|
|Sub Controller |When the calculation is defined, “CALC” is displayed on the tree view, in respective of the number of defined calculations.| R |R|
|Actual Status |Current control Status | R |R|
|Desired Status| Calculation status can be selected. Selection is available on ENG mode. ACTIVE INACTIVE ACTIVE Calculation is executed and the result is displayed on the screen. When the DCS tag name is defined as output address, the calculation result is sent to DCS. INACTIVE Calculation is executed, but the result is not displayed on the screen nor output to DCS. On the MC/SC overview panel, the previously calculated value remains.| R| R/W|
|Comment |Controllerˇs Comments (16 Characters) |R |R|
2017.1.4
